Information

Title	Gateway Firmware v3.6.0

URL Name	ka03o000001DtZsAAK

Article Details

Body

Note: Please contact Enlighted Support before proceeding with the upgrade

Gateway v3.6.0 release notes:

Upgrade Path

Users can upgrade directly from Gateway firmware v2.8.36 to v3.6 by following the procedure described in the article Upgrading Gateway Firmware from v2.8.36 to v3.x.
For Gateways running firmware earlier than v2.8.36, follow the procedure described in Upgrading Gateway Firmware from v2.6.x to v2.8.36, then upgrade it to v3.x or higher.

Enhancements

The Enlighted Gateway 3.6 release provides the following new features:

Cross Gateways Switch Groups
802.1x Certificate Update Ability
Enlighted Edge Gateway Support
Ability to Disable Port 8085 for Manage in Cloud Deployments
Improved Accuracy in RF Radio Center Frequency
IPV6 Networking Support

Features

Cross Gateways Switch Groups

Individual Switch and Motion groups on a single Gateway can belong to Switch or Motions Groups across Gateways in Edge. Edge will listen to the Gateway traffic for local Switch or Motion commands and broadcast those commands to Switch and Motion Group sensors on other Gateways. Users can create Cross-Gateway Switch Groups (Single Floor) and Cross-Gateway Motion Groups (Single Floor) in Manage v4.9 and above. The Switch or Motion identifiers and the Gateway MAC ID associated would be expressed to Edge from Manage as a look-up table.
Gateways will be able to see sensor-to-sensor motion radio traffic.
The X300 device and Edge Software must be installed and available in the Enlighted lighting network.

802.1x Certificate Update Ability

The 802.1x certificate is required for authentication to the Gateway. v3.6.0 adds the ability for Manage to update this certificate.

Enlighted Edge Gateway Support

The Enlighted Edge provides low-latency (real-time) lighting control interfacing with third-party systems such as BACnet/IP for BMS integrations. It will also enhance lighting control through Cross Gateway Switch and Motion groups to communicate across Gateways.

Ability to Disable Port 8085 for Manage in Cloud (EMC) Deployments

On startup, the Gateway will listen on Port 8085 to connect to on-premise Manage devices before connecting to Enlighted Manage in the Cloud (EMC). With this release, the Gateway will not listen to Port 8085 for connecting to on-premise Manage devices.

Improved Accuracy in RF Radio Center Frequency

This release offers an improved and accurate RF Radio center frequency.

IPv6 Networking Support

Version 3.4.0 and later of the Enlighted Gateway now supports connecting to Manage in the Cloud using IPv6. This feature can be enabled using the Custom Network Configuration feature.

Important Note: For 3.6 firmware, if you enable IPv6, please change the "Amaze API Server" and "Amaze Device Server" to v6-device.enlightedinc.com.

Internal Enlighted users: If using Beta3, set the fields to vy-b-device.enlightedinc.com (not a link).

Limitations

None

Supported Gateway

Release 3.6 is compatible with Enlighted Gateway Gen 2/V2, Product Code (GW-2-01).

Recommended Firmware Versions

The following table provides the supported releases, including the recommended device firmware versions to be used with this release.

Device	Recommended Firmware Version	Firmware Image
Note: Release Notes and firmware images are available only for registered Partners & Customers.
Manage	Manage 4.0 or higher	Contact Enlighted Support
Gen 5 Sensors	v5.9.4 or higher	See Gen 5 Sensor Firmware Releases section
Gen 4 Sensors	v5.1.34 or higher	See Gen 4 Sensor Firmware Releases section
Gateway	v3.6.0	3.6.0 image; see Attachments below
Upgrade Path	v3.6.0	2.6.x > 2.8.36 > 3.x
Plug Load Controller	Supports any version	Plugload Image, v3.1
ERC Switch	Supports any version	ERC Image, v4.2.0. Older ERC versions: v2.7.3, v.4.1.10 are also supported.

GNU Public License Notice

The Enlighted Gateway 3.6 uses the open-source software BusyBox (https://busybox.net) version 1.31.1.

It is a version built as part of the Buildroot package (https://buildroot.org) version 2020.02.6, and includes patches to BusyBox.

Enlighted has made no modifications to the BusyBox code.

Enlighted will provide this source code upon request, or it is available here:

Buildroot 2020.02.6: https://buildroot.org/downloads/buildroot-2020.02.6.tar.gz
Busybox 1.31.1: https://busybox.net/downloads/busybox-1.31.0.tar.bz2

Gateway Firmware v3.6.0