Emergency Lighting Solutions
Emergency lighting solutions exist for fixtures with either Control Units or IoT Ready Profile 0 Drivers. Specification Sheets for all supported devices are found at the bottom of this page. The following emergency lighting solutions are described here.
- Emergency Lighting with Control Unit (CU-4E-FMH)
- Emergency Lighting with IoT Ready Profile 0 Drivers
- Emergency Lighting with IoT Ready Profile 1 Drivers: Not Supported
- Emergency Lighting with DALI Drivers
1. Emergency Lighting with Control Unit (CU-4E-FMH)
There is NO Emergency version of the CU-4E, so a separate UL924 device is required in all Emergency Fixtures.
Enlighted Available UL924 Devices
We have tested and qualified multiple UL924 devices with the CU-4E. The table below summarizes the devices that we can supply directly.
Product Code | Manufacturer and Part Number | Line Diagram | Line Diagram |
---|---|---|---|
UL924-FD-BSR-120V |
Functional Devices ESR2401D |
ESR2401D Nipple Mount Relay, 120V only |
|
UL924-FD-BSR-208V-277V |
Functional Devices ESR2402D |
ESR2402D Nipple Mount Relay, 208-277V only |
|
UL924-FD-ESRB |
Functional Devices ESRB NOTE: The ESRLBCND is preferred over the ESRB. Please use ESRLBCND for all new designs. |
ESRB Fixture Mount Relay, 120-277 |
|
Fixture Mount Relay 120-277V with Ecosense Dimming |
SU-5 and CU-4 with ESRB and Ecosense for Emergency Line Dimming Control, 93-02845-02 |
||
UL924-FD-ESRN |
Functional Devices ESRN |
ESRN Nipple Mount Relay, 120-277V |
|
ESRN Nipple Mount Relay 120-277V for Pendant Lighting Application |
ESRN Nipple Mount for Pendant Lighting Application, 93-02946-01 |
||
UL924-ESRLBCND |
Functional Devices ESRLBCND NOTE: The ESRLBCND is preferred over the ESRB. Please use ESRLBCND for all new designs. |
ESRLBCND Fixture Mount Zero Delay Relay, 120-277V |
UL924 ESRLBCND Device with Control Unit (03166-02) |
Other UL924 Devices
Manufacturer and Part Number | Line Diagram | Line Diagram |
---|---|---|
LVS RRU-X-UNV |
RRU-X-UNV Fixture Mount Shunt Relay |
|
EPC-1-D-HV |
Profile 0, 0-10V Driver, with SU-5 IoT Ready UL924 347 VAC |
Profile 0, 0-10V Driver, with SU-5 IoT Ready UL924 347 VAC (03136-02) |
2. Emergency Lighting with IoT Ready Profile 0 Drivers
Profile 0 drivers are 0-10V analog dimming drivers with an auxiliary DC voltage output that powers the sensor directly. No control unit is used with Profile 0 Drivers.
In the Emergency condition, the 0-10V dimming signal must be disconnected so the fixture will come on at full intensity. This allows a different set of UL924 devices to be used.
Enlighted Available UL924 Devices
Product Code | Manufacturer and Part Number | Description | Line Diagram |
---|---|---|---|
UL924-FD-BSR-120V | Functional Devices ESR2401D | Nipple Mount Relay, 120V only | Profile 0, 0-10V Driver with SU-5 IoT Ready UL924, 93-02766-04 |
UL924-FD-BSR-208V-277V | Functional Devices ESR2402D | Nipple Mount Relay, 208-277V only | Same as above |
Other UL924 Devices
Supported but not stocked by Enlighted. These devices must be ordered directly from the manufacturer or via distribution.
Manufacturer and Part Number | Description | Line Diagram |
---|---|---|
Functional Devices ESR01P | Nipple Mount Relay, 120V only | Profile 0, 0-10V Driver with SU-5 IoT Ready UL924, 93-02766-04 |
Functional Devices ESR02P | Nipple Mount Relay, 208-277V only | Same as above |
3. Emergency Lighting with IoT Ready Profile 1 Drivers
Not supported. Use Control Unit or Profile 0 alternatives for Emergency Lighting.
4. Emergency Lighting with DALI Drivers
Emergency lighting with DALI drivers is handled differently in North America (NA) vs other regions of the world. In NA, a bypass switching device often referred to as a UL924 device, is used to disable or bypass the lighting controls. In other regions, a special DALI device type, Device Type 1 (DT1), defined in part 202 of the DALI standard (EN62386-202) is typically used. Enlighted supports both approaches as detailed in the sections below.
- For North America applications, see the line diagram showing the connections between an Enlighted SU-5, 2-wire sensor with UL924 SPST device, 2-wire driver, and an internal Power Supply Unit (PSU): UL924 Generic SPST, 2-wire with a Normal and Emergency Driver with Internal PSU (03131-06)
- For non-North American applications a single DALI Type 1 emergency driver can be connected to a sensor. This is illustrated in SU-5 2-wire with DALI Drivers and External PSU with Emergency EU 03381-01 and SU-5 2-wire with SR Driver and LED with Emergency EU-03380-01.
The status of the emergency driver can be tested by use of the DALI Emergency APIs. Since only a single emergency driver is connected to a sensor, the location of any failing emergency driver is immediately identifiable in the system.
UL924 Device Specifications
Functional Devices
https://www.functionaldevices.com/products/lighting-controls/ul924-emergency-relays/
Data Sheets for the following devices can be found below :
- ESRB and ESRN - Specification Sheet for ESRB (fixture mount) and ESRN (nipple mount) devices
- ESR2401D - Specification Sheet (120VAC )
- ESR2402D - Specification Sheet (208-277VAC)
- ESR01P - Specification Sheet (120VAC)
- ESR02P - Specification Sheet (208-277VAC)
- ESRLBCND - Specification Sheet (120-277VAC)
LVS
http://www.lvscontrols.com/rru-x-unv.php
- RRU-X-UNV - Specification Sheet:
Downloads:
Canadian Emergency Lighting
For Canadian installations where the mains voltage is frequently 347 VAC, the emergency lighting solutions available for these types of fixtures require either IoT Ready Profile 0 (Dim to off) Drivers or 0-10VDC Dimming Drivers with SR Bridge.
Emergency Lighting with 347VAC IoT Ready Profile 0 Drivers
Profile 0 drivers are 0-10V analog dimming drivers with an auxiliary DC voltage output that powers the sensor directly. No control unit is used with Profile 0 Drivers. In the Emergency condition, the 0-10V dimming wires connected to the UL924 device will allow the fixture to come on at full intensity.
Emergency Lighting with 347VAC 0-10VDC Dimming Drivers with SR Bridge
0-10VDC Dimming Drivers use the Signify Sensor Ready (SR) Bridge to allow the Enlighted 2-wire sensor to control fixtures with 347VAC drivers. In the Emergency condition, the 0-10 dimming wires connected to the UL924 device will allow the fixture to come on at full intensity.
The UL924 Devices listed below are supported but not stocked by Enlighted. These devices must be ordered directly from the manufacturer or via distributor.
Manufacturer and Part Number | Description | Line Diagram |
---|---|---|
LVS UL924 EPC-1-D-HV, LVS | LVS Emergency power, 347V only Profile 0 (Dim-to-Off) Driver | Profile 0, 0-10V Driver, with SU-5 IoT Ready UL924 347 VAC (03136-02) |
LVS UL924 EPC-1-D-HV, LVS | LVS Emergency power, 347V only 0-10VDC Drivers, with SR Bridge | SU-5, 2-wire Sensor with Profile 0 Drivers, SR Bridge, and UL924 Device, 347 VAC (03181-02) |
Other UL924 Devices
This Line Diagram given in the following table is for LVS UL924 device and 120-277VAC application.
Manufacturer and Part Number | Description | Line Diagram |
---|---|---|
LVS RRU-X-UNV |
RRU-X-UNV Fixture Mount Shunt Relay |
Recommended articles:
- Refer to the article Canadian Wiring 347 VAC Solutions for a list of 347 VAC drivers compatible with 2-wire Gen 5 (SU-5) sensors when used with an XSR bridge.
- Refer to DALI Solutions for a brief overview of the solutions offered.
Canadian Wiring 347 VAC Solutions
For Canadian installations where the mains voltage is frequently 347 VAC, which is beyond the limits of the Enlighted Control Unit (CU-4E), Enlighted suggests the following 347 VAC drivers that are compatible with the 2-wire SU-5 sensors when used in conjunction with an XSR Bridge. The following list of DALI drivers and 0-10V drivers can be used directly with the Enlighted 2-wire sensors with an XSR Bridge.
DALI Drivers with Built-in Power Supply Unit and Power Metering Function
When you select one of the following listed drivers, the driver provides sensor powering and supports the DALI Power Metering function directly.
Manufacturer | Model Number | Certifications | Power Rating (W) |
Input Voltage Range (VAC/DC) |
Output Current (mA) |
Output Voltage Range (VDC) |
Dimming Type |
PSU in the Driver (Yes/No) |
Power metering function (Yes/No) |
Philips/Signify | XJ180C090V285VSF2M | UL ETL CSA D4i | 180 | 277 - 480 | 100 - 900 | 100 - 285 | DALI Log 10 - 100% and DALI Linear 10 - 100% | Yes | Yes |
Philips/Signify | XJ180C125V210VSF2M | UL ETL CSA D4i | 180 | 277 - 480 | 100 - 1250 | 70 - 210 | DALI Log 10 - 100% and DALI Linear 10 - 100% | Yes | Yes |
Philips/Signify | XJ180C180V144VSF2M | UL ETL CSA D4i | 180 | 277 - 480 | 100 - 1800 | 50 - 144 | DALI Log 10 - 100% and DALI Linear 10 - 100% | Yes | Yes |
DALI Drivers without Power Supply Unit or Power Metering Function
When you select one of the following listed drivers, an External DALI PSU is required. To set up Soft Metering, the fixture manufacturer must provide the power consumption vs dimming setting.
Manufacturer | Model Number | Certifications | Power Rating (W) |
Input Voltage Range (VAC/DC) |
Output Current (mA) |
Output Voltage Range (VDC) |
Dimming Type |
PSU in the Driver (Yes/No) |
Power metering function (Yes/No) |
ULT | D700C30347D-C | UL | 30 | 347 VAC | 700 | 15 - 44 | DALI 1% | No | No |
ULT | D10CC30347D-C | UL | 30 | 347 VAC | 1050 | 15 - 44 | DALI 1% | No | No |
ULT | D10CC55347D-C | UL | 55 | 347 VAC | 1050 | 11 - 29 | DALI 1% | No | No |
ULT | D15CC55347D-C | UL | 55 | 347 VAC | 1500 | 15 - 37 | DALI 1% | No | No |
ULT | D21CC80347D-D | UL | 80 | 347 VAC | 2100 | 11 - 38 | DALI 1% | No | No |
ULT | D10CC55347D-K/KS | UL | 55 | 347 VAC | 1050 | 11 - 29 | DALI 1% | No | No |
ULT | D15CC55347D-K/KS | UL | 55 | 347 VAC | 1500 | 15 - 37 | DALI 1% | No | No |
0-10V Profile 0 Dimming LED Drivers
The list of 0-10V drivers is available at different power levels from 20 to 95 watts to meet various luminaire size requirements. You can use multiple drivers with a single 2-wire sensor and the XSR-Bridge.
Manufacturer | Model Number | Certifications | Power Rating (W) | Input Voltage Range (VAC) | Output Current (mA) | Output Voltage Range (VDC) | Dimming Type |
Osram | OTi 30/347/1A0 DIM L AUX | UL | 30 | 347 | 350 - 1050 | 10 - 55 | 0 - 10V 10% |
Osram | OTi 48/347/2A0 DIM L AUX | UL | 48 | 347 | 700 - 2000 | 10 - 55 | 0 - 10V 10% |
Osram | OTi 48/347/2A0 DIM-1 L AUX | UL | 48 | 347 | 700 - 2000 | 10 - 55 | 0 - 10V 1% |
Osram | OTi 50/347/1A4 DIM L AUX | UL | 50 | 347 | 400 - 1400 | 10 - 55 | 0 - 10V 10% |
Osram | OTi 85/347-480/2A3 DIM-1LHB AUX | UL | 85 | 347 - 480 | 700 -2300 | 10 - 55 | 0 - 10V 10% |
Osram | OTi 85/347-480/2A3 DIM-1 L AUX | UL | 85 | 347-480 | 700 - 2300 | 10 - 55 | 0 - 10V 10% |
Osram | OTi 95W/UNV/2750C/2DIM+/P6/AUX | UL | 95 | 347-480 | 700 - 2750 | 15 - 54 | 0 - 10V 1% |
This solution with the XSR bridge is only for 2-wire sensors; the 2-wire sensor connects to the XSR bridge. See the line diagram SU-5 (2-wire) with XSR Bridge and (347v) 0-10v Driver (03066-02), which is the most preferred solution.
An alternative method, when energy metering is not required, uses a 347 VAC Profile 0 driver with an 8-pin sensor and adapter cable. In this case, the sensor is powered from the Auxiliary DC supply of the driver. Refer to the following line diagrams:
- Profile 0 Driver with SU-5 Sensor (02736-06).
- Profile 0, 0-10V Driver, with SU-5 IoT Ready UL924 347 VAC (03136-02)