Asset Tag (AT-1U-H1) Install Guide
Download the Asset Tag Installation Guide.
Shipped Components
- Asset Tag (AT-1U-H1)
Supplemental Components
- Mounting Bracket (BRKT-AT-1U)
-
A pack of Zip Cable Ties
Asset Tags Placement Guidelines
The placement and positioning of Asset Tags are important for an unobscured line of sight to the sensors on the ceiling. Here is a guideline of recommended locations for Asset Tags.
Office or Medical Devices: The ideal location is to place the Asset Tag on top of the device. The order of preference is to place the tag.
- On top of the device with the Enlighted Logo of the Asset Tag facing up.
- If the surface is metal, make sure the Enlighted logo of the Asset Tag is facing up.
- On side of the device at the highest unobscured location, or on insulation plastic panel, vertically oriented with the button facing upwards.
- On side of the device at the highest unobscured location, or if the surface is metal, place the tag vertically oriented with the button upwards.
Do not place the tag:
- On the bottom of the device without any clear view to the ceiling, or
- In an obscured location, for example, inside a cavity, etc.
Installation Steps
The tag must be activated before use and added to the BlueGPS application.
Activating the Tag
Refer to the article Activating Tags.
Mounting the Tag to a Flat Surface
Step 1: Remove the adhesive cover from the tag's back and securely attach the Asset Tag to the equipment, following the recommended placement guidelines.
Mounting the Tag to a Curved Surface using the Bracket
The Asset Tag can be secured to a structure with a curved surface, such as a chair leg, equipment post, etc., using the mounting bracket and cable ties (BRKT-AT-1U). Determine if the Asset Tag requires a bracket to be mounted. If yes, follow the procedure below.
Step 1: Insert the tapered end of the tie through the upper slot in the bracket.
Step 2: Insert a second tie through the lower slot in the bracket.
Step 3: Hold the bracket and loop the cable ties around the curved surface of the structure.
Step 4: Pull the tapered end of the tie through the back of the tie head. Repeat this for the second tie until the bracket attaches itself snugly to the structure.
Step 5: Remove the adhesive cover from the back of the tag.
Step 6: Securely attach the asset tag to the mounting bracket.
Product Compliance
Note: The battery cannot be replaced in an Asset Tag. Order a new Asset Tag (AT-1U-H1) when the battery is low.
Battery Caution: Chemical Burn Hazard. This product contains a coin cell battery. If the battery is swallowed, it can cause severe internal burns and can lead to death. Keep new and used batteries away from children. If you think batteries might have been swallowed, seek immediate medical attention.
Model: AT-1U-H1
FCC ID: AQQ-AT1U
IC: 10138A-AT1U
Rev.08
Regulatory Compliance Certification
Downloads:
Activating Tags
All Asset and Badge tags must be activated before use.
Activating an Asset Tag
To activate the tag,
- Press and hold the button for 10 seconds until the LED flashes, and then release the button.
The LED blinks orange for five seconds to confirm that the activation sequence has been detected and the tag is ready.
After that, the LED lights up solid orange for two seconds whenever the button is pressed and released.
Activating a Badge Tag
- Press and hold the button for five seconds until the LED blinks green, and then release the button.
- Press and hold the button for 10 seconds to remove it from the factory mode setting.
After that, the LED blinks solid green whenever the button is pressed and released.
Bluetooth Capabilities & Settings
Bluetooth (BLE) Tags such as Asset or Badge tags are placed on equipment, devices, and staff badges. By tagging individual assets with a Bluetooth Low Energy (BLE) tag, the Enlighted's IoT network can quickly and reliably track equipment and locate people in real-time. However, sometimes due to the volume of data collected by the sensors and reported to Manage, it may sometimes lead to heavy traffic load, packet loss, and network congestion. To reduce congestion in the network, you can configure the Bluetooth Tag Settings in Manage. Please refer to the following links:
- Configure Bluetooth Tag Settings in Manage
- Configure Location Accuracy Parameters in Manage
- Read the BLE Capabilities Application Note
BlueGPS User Guide
The in-app Help allows users to open Help content in the app. Please obtain your email and password from your company IT administrator.
- Sign In to Enlighted BlueGPS. The BlueGPS Application and Documentation tabs display.
- Click the Documentation tab to view the User Guide.
The User Guide displays with categories on the left-navigation panel.
BlueGPS API User Guide
The in-app Help allows users to open the API Help content in the app. Please obtain your email and password from your company IT administrator.
- Sign In to Enlighted BlueGPS. The BlueGPS Application and Documentation tabs display.
- Click the Documentation tab to view the Blue GPS User Guide.
- Click the Swagger icon at the top-right of the page to view the BlueGPS API documentation.
- You can then select a definition filter from the top-right dropdown menu.