Gen 5 Sensor Wiring Test Results

Download the Gen 5 Sensor Wiring Test report for the various sensor firmware releases. 

The Sensor LED indicates the Wiring Test results after the wiring test has been run.  In addition to the table below, you can find the LED indicator patterns for specific firmware versions in the Firmware release notes for that version.  Links in the table below provide access to the FW release notes.  In general,   

  • Solid GREEN indicates that the wiring test is completed, the sensor is waiting to be discovered.
  • Blinking BLUE indicates that the wiring test is completed and it did not detect an energy metering device.
  • Blinking RED indicates the test is complete with a few exceptions corresponding to a common error state. This could be due to any of the following reasons:
    • The fixture power level is too low, and the power change is too small to be deemed different enough.
    • In a few fixture designs, a non-dimmable driver is connected. The fixture does not support dimming and needs ON/OFF control from the sensor.
    • The driver power efficiency is low, which rendered the power consumption of total output vs. low dim level output to be both at a high overhead power consumption level, which narrowed down the power consumption differences among the different dimming setting levels, and 
    •  If none of the above, it may be due to wrong wiring, which the fixture manufacturer needs to troubleshoot.

The report describes the lighting sequence for the sensor wiring test when powered on and the LED status at the end of the wiring test.

Gen 5 Sensor Wiring Test Results for Sensor Firmware
Lighting Sequence and Sensor LED Behavior
Version: 4.0 as of Oct 14, 2021

*Note: with multiple DALI drivers connected to an Enlighted 2-wire sensor, each of the drivers will go through the "Power ON Lighting Sequence" one by one, and at the end of the last driver finishing the sequence, the sensor will indicate the test result as "End of Wiring Test LED Behavior" shows.

CU includes the following devices, CU-4E-FMH, CU-4E-NMI, CU-4E-NME and DALI CU  

Firmware Version Stand-alone Sensor
[Not connected to Control Unit (CU) or LED driver]
Connected to CU with one or more 0-10V Drivers Connected to CU with Single
Non-dimmable Driver
Sensor Connected to Profile Zero Driver 2-wire sensor connected to single* DALI driver
  Power ON Lighting Sequence  End of Wiring Test
LED Behavior
Power ON Lighting Sequence
Time 's' - Seconds
End of Wiring Test
LED Behavior
Power ON Lighting Sequence End of Wiring Test
LED Behavior
Power ON Lighting Sequence End of Wiring Test
LED Behavior
Power ON Lighting Sequence
Time 's' - Seconds
End of Wiring Test
LED Behavior
5.12.11 Not Applicable Blinking BLUE

ON (100%)-10s
Dim ON (80%)-1s ON (100%) 4s
OFF (0%)-4s
ON (100%)-4s
OFF (0%)-4s
Dim ON (20%)-4s
OFF (0%)-4s
ON (100%)-1s
OFF (0%)-4s
ON (100%)-2mins
Dim down (65%)

Wiring test completed, lights at 65%

Solid GREEN

ON (100%)-34s
OFF (0%)-4s
ON (100%)

Wiring test completed, lights at 100%

Blinking RED

OFF (0%)-7s
ON (100%)-4s
OFF (0%)-4s
ON (100%)-4s
OFF (0%)-4s
Dim ON (20%)-4s
OFF (0%)-4s
ON (100%)-2 mins
DimDown (65%)

Wiring test completed, lights at 65%

Blinking BLUE

ON (100%)-15s
OFF (0%)-4s
ON (100%)-4s OFF (0%)-4s
Dim ON (20%)-4s OFF (0%)-4s Dim ON (10%)-1s OFF (0%)-4s
ON (100%) 2mins
DimDown (65%)

Wiring test completed, lights at 65%

Solid GREEN
5.11.8 Not Applicable Blinking BLUE

ON (100%)-4s
OFF (0%)-4s
ON (80%)-1s ON (100%) 4s
OFF (0%)-4s
ON (100%)-4s
OFF (0%)-4s
Dim ON (20%)-4s
OFF (0%)-4s Dim ON (10%)-4s
OFF (0%)-4s
ON (100%)-1s
OFF (0%)-4s
ON (100%)-2mins
Dim down (65%)

Wiring test completed, lights at 65%

Solid GREEN

ON (100%)-34s
OFF (0%)-4s
ON (100%)

Wiring test completed, lights at 100%

Blinking RED

OFF (0%)-7s
ON (100%)-4s
OFF (0%)-4s
ON (100%)-4s
OFF (0%)-4s
Dim ON (20%)-4s
OFF (0%)-4s Dim ON (10%)-4s
OFF (0%)-4s
ON (100%)-2 mins
DimDown (65%)

Wiring test completed, lights at 65%

Blinking Blue

ON (100%)-18s
OFF (0%)-4s
ON (100%)-4s
Dim ON (20%)-4s Dim ON (10%)-4s
ON (100%) 2mins
DimDown (65%)

Wiring test completed, lights at 65%

Solid Green
5.9.4 Not Applicable Blinking BLUE

ON (100%)-4s
OFF (0%)-4s
ON (80%)-1s ON (100%) 4s
OFF (0%)-4s
ON (100%)-4s
OFF (0%)-4s
Dim ON (20%)-4s
OFF (0%)-4s
ON (100%)-1s
OFF (0%)-4s
ON (100%)-2mins
Dim down (65%)

Wiring test completed, lights at 65%

Solid GREEN

ON (100%)-34s
OFF (0%)-4s
ON (100%)

Wiring test completed, lights at 100%

Blinking Red

OFF (0%)-7s
ON (100%)-4s
OFF (0%)-4s
ON (100%)-4s
OFF (0%)-4s
Dim ON (20%)-4s
OFF (0%)-4s Dim ON (10%)-4s
OFF (0%)-4s
ON (100%)-2 mins
DimDown (65%)

Wiring test completed, lights at 65%

Blinking BLUE

ON (100%)-14s
OFF (0%)-4s
ON (100%)-4s
Dim ON (20%)-4s
ON (100%) 2mins
DimDown (65%)

Wiring test completed, lights at 65%

Solid GREEN
5.5.14 Not Applicable Blinking BLUE ON (100%)-3s
OFF (0%)-3s
ON (100%)-3s
OFF (0%)-3s
ON (100%)-3s
OFF (0%)-3s
Dim ON (20%)-3s
OFF (0%)-3s
ON (100%)-0.5s
OFF (0%)-4s
ON (100%)-2mins
Dim down (65%)

Wiring test completed, lights at 65%
Solid GREEN ON (100%)-38s
OFF (0%)-4s
ON (100%)

Wiring test completed, lights at 100%
Blinking RED OFF (0%)-7s
ON (100%)-4s
OFF (0%)-4s
ON (100%)-4s
OFF (0%)-4s
ON dim (20%)-4s
OFF (0%)-4s
ON (100%)-2 mins
DimDown (65%)

Wiring test completed, lights at 65%
Blinking BLUE ON (100%)-3s
OFF (0%)-3s
ON (100%)-3s
OFF (0%)-3s
ON (100%)-3s
OFF (0%)-3s
Dim ON (20%)-3s
OFF (0%)-3s
ON (100%)-0.5s
OFF (0%)-4s
ON (100%)-2mins
Dim down (65%)

Wiring test completed, lights at 65%  
Solid GREEN
5.1.59 Not Applicable Blinking BLUE ON (100%)-3s
OFF (0%)-3s
ON (100%)-3s
OFF (0%)-3s
ON (100%)-3s
OFF (0%)-3s
Dim ON (20%)-3s
OFF (0%)-3s
ON (100%)-0.5s
OFF (0%)-4s
ON (100%)-2mins
Dim down (65%)

Wiring test completed,lights at 65%
Solid GREEN

ON (100%)-38s
OFF (0%)-4s
ON (100%)

Wiring test completed, lights at 100%

Blinking RED

OFF (0%)-3s
ON dim (20%)-4s
ON (100%)-5s
OFF (0%)-4s
ON (100%)-4s
OFF (0%)-4s
ON dim (20%)-4s
OFF (0%)-4s
ON (100%)-2mins
DimDown (65%)

Wiring test completed, lights stay at 65%

Blinking BLUE

ON (100%)-3s
OFF (0%)-3s
ON (100%)-3s
OFF (0%)-3s
ON (100%)-3s
OFF (0%)-3s
Dim ON (20%)-3s
OFF (0%)-3s
ON (100%)-0.5s
OFF (0%)-4s
ON (100%)-2mins
Dim down (65%)

Wiring test completed,lights at 65%

Solid GREEN
5.0.20 Not Applicable Blinking RED ON (100%)-3s
OFF (0%)-3s
ON (100%)-3s
OFF (0%)-3s
ON (100%)-3s
OFF (0%)-3s
Dim ON (20%)-3s
OFF (0%)-3s
ON (100%)-0.5s
OFF (0%)-0.5s
ON (100%)

Wiring test completed, lights stay at 100%
Solid GREEN ON (100%)-36s
OFF (0%)-3s
ON (100%)

Wiring test completed, lights stay at 100%  
Blinking RED ON Dim (20%)-7s
ON (100%)-2 mins
DimDown (65%)

Wiring test completed, lights stay at 65%
Blinking RED

ON (100%)-3s
OFF (0%)-3s
ON (100%)-3s
OFF (0%)-3s
ON (100%)-3s
OFF (0%)-3s
Dim ON (20%)-3s
OFF (0%)-3s
ON (100%)-0.5s
OFF (0%)-0.5s
ON (100%)

Wiring test completed, lights stay at 100%

 

Solid GREEN
4.0.85 Not Applicable Blinking RED ON (100%)-3s 
OFF (0%)-3s 
ON (100%)-3s 
OFF (0%)-3s  
ON (100%)-0.5s
OFF (0%)-0.5s 
Dim ON (20%)-0.5s 
OFF (0%)-0.5s
ON (100%)-0.5s
Dim Down (65%)

Wiring test completed, lights stay at 65%
Solid GREEN ON(100%)-36s
OFF (0%)-3s
ON (100%)

Wiring test completed, lights stay at 100%  
Blinking RED ON Dim (20%)-2s
DimUP (100%)-0.5s
DimDown (65%)

Wiring test completed, lights stay at 65%   
Blinking RED

ON (100%)-3s
OFF (0%)-3s
ON (100%)-3s
OFF (0%)-3s
ON (100%)-0.5s
OFF (0%)-0.5s
Dim ON (20%)-0.5s
OFF (0%)-0.5s
ON (100%)-0.5s
Dim Down (65%)

Wiring test completed, lights stay at 65%

 

Solid GREEN

 

Downloads:

Was this article helpful?
0 out of 1 found this helpful
Have more questions? Submit a request

Comments

Article is closed for comments.