Micro Sensor with 2-wire Adaptor (KIT-SU-5E-D)

Download the Micro Sensor with 2-wire adaptor Installation Guide PDF: English rev.04 | German rev.04 | French rev.04

Overview

The Enlighted Micro Sensor with 2-wire Adaptor delivers all the functionality of our other sensors in a minimally-sized package. It is designed to be easily mounted into lighting fixtures or ceiling tiles such that only the discreet white faceplate is visible. The sensor slides into a carrier sleeve, fitting a standard 1/2 inch trade size knockout or 7/8 inch (22 mm) hole. Carrier sleeves compatible with either lighting fixtures or ceiling tiles are available. Sensor replacement requires no tools—slide the sensor out of the carrier, unplug the connector, and install the new sensor.

Capture.JPG 

Micro Sensor with 2-wire Adaptor Cable

The following sections describe installing the Micro sensor 2-Wire adaptor in a fixture or tile.

If you have purchased the Hard Ceiling Mount Carrier (HCMC-SU-5E) as an optional component for installing the sensor, refer to the following articles:

Installation

Shipped Components

Supplemental Components

Tools you may Need

  • 7/8” Drill bit (1/2” knock out trade size)
  • Hand drill
  • Wire stripper

* Indicated products are sold separately. Contact  Enlighted Customer Support.

Caution

A qualified electrician must perform the installation and maintenance under the local, state, and national electrical codes (NEC) and requirements.

Fixture Mount Sensor Installation

Note: For fixture mounting, use the fixture carrier and nut that is shipped with the sensor. The fixture mount can accommodate up to 0.25” thickness materials.

mceclip0.png

Fixture Carrier and Nut

Step 1: De-energize the luminaire.

Step 2: Determine the sensor's location in the fixture and cut a ½ inch (7/8” diameter) knockout in the fixture.

mceclip1.png

Step 3: Insert the fixture carrier through the hole in the fixture.

Step 4: From behind the fixture, align the tabs of the nut with the keys on the fixture carrier.

mceclip2.png

Step 5: Slide the tabs of the nut along with the keys of the carrier to fasten the carrier.

Zd_Step_1_Callouts.png

Picture3.png

Step 6: Connect the adaptor cable to the sensor.

Step_6.png

Step 7: Cut two lengths of 18 AWG solid wire of the required length. Strip each end of the two wires leaving 3/8 inch of exposed wire.

Step 8: Insert one end of the pair of wires through the hole in the fixture and connect the wires to the sensor.

Step_8_Fixture.png

 

Step 9: Guiding the wire from above, push the sensor into the carrier until it securely clicks into the carrier.

Step_9_Fixture.png

Step 10: Leave four inches of slack cable in the sequence loop to avoid pinching the cable and bring the sensor down if it needs to be replaced.

Note: Do not pull the cable forcefully, as this might damage the cable or connector.

Step 11: See section Connecting the Cable to the LED Driver.

Tile Mount Sensor Installation

Note: For tile mounting, the tile carrier and nut must be ordered separately. The tile mount can accommodate up to 1.5” thick tiles.

mceclip7.png

Tile Carrier and Nut

Step 1: De-energize the luminaire.

Step 2: Make a 7/8th diameter hole in the ceiling tile.

Step 3: Insert the tile carrier through the hole into the tile.

mceclip8.png

Step 4: Thread the plain end of the nut from behind the tile to secure the carrier.

mceclip9.png

If the tile is thicker than normal, flip the nut and thread the nut's ribbed end to secure the carrier.

Step 5: Insert the adaptor cable into the sensor.

Step_6.png

Step 6: Cut two lengths of 18 AWG solid wire of the required length. Strip each end of the two wires leaving 3/8 inch of exposed wire.

Step 7: Insert one end of the wires through the hole in the tile and connect the wires to the sensor.

Step_7_Tile.png

Step 8: Guiding the wire from above, push the sensor into the carrier until it securely clicks into the carrier.

Step_8_Tile.jpg

Step 9: Leave four inches of slack cable in the sequence loop to avoid pinching the cable and bring the sensor down if it needs to be replaced.

Note: Do not pull the cable forcefully, as this might damage the cable or connector.

Step 10: See section Connecting the Cable to the LED Driver.

Connecting the Cable to the LED Driver

Step 1: Connect the other end of the pair of wires to the LED Driver.

Picture4.png

Step 2: Turn the power on by switching on the circuit breaker and wait for the green LED to appear.

LED Description

LED Status Description/Solution
LED not on Power issue or faulty sensor. Check power and wiring
Blinking Green The commissioned sensor has powered up and has detected motion. If there is no motion in the sensor’s field of view, the blinking will stop. Wave your hands below the sensor to restart LED blinking.
Solid Green The un-commissioned sensor has powered up successfully and passed the wiring test –waiting for discovery.
Blinking Red The un-commissioned sensor has powered up and detected a wiring test issue. Check the wiring.
Solid Red Faulty sensor –replace the sensor.
Solid Blue The sensor received a request to identify itself.
Blinking Blue The un-commissioned sensor was not able to detect an energy measurement device (Control Unit or Driver).

Product Compliance

Picture6.pngmceclip0.png mceclip1.png CE_logo.pngmceclip2.pngrcm_image.gif Japan.jpg 

Model No. SU-5E-01
Product Code: KIT-SU-5E-D-xxx
xxx: IoT Note (IoT), Connected Lighting (CL), Independent Lighting/Enlighted One (IL)
FCC ID: AQQ-SU5E
IC: 10138A-SU5E
Rev.04
DoC: enlightedinc.com/eu-docs/mceclip1.png

Recommended articles:

Downloads:

Was this article helpful?
0 out of 0 found this helpful
Have more questions? Submit a request

Comments

Article is closed for comments.