- How many models of Control units are there, and what is the difference between them?
- How many control units can I connect to one sensor?
- Why are there two 0-10v channels on the CU-4E?
- Why don't the Enlighted Control Units work with all Bodine-based Emergency LED Drivers?
- Does the emergency control unit CU-3E work with fixtures provided with an integral battery pack or just with an emergency system supply such as a generator/inverter? Is there any additional control wiring to connect the emergency control unit to sense loss of power?
- What's the difference between earlier versions of the Control Unit and the new CU-4E?
- How can I dim incandescent fixtures with your CU?
- If we replace CUs, do you need to come back to the program?
- Why doesn't Enlighted manufacture their own Emergency Control Unit?
- What is the power output voltage for CU-4E?
- What is the CU-4E power metering accuracy?
- Does the Control Unit (CU) output a linear or logarithmic 0-10v dimming?
- What are the distinguishing factors for using the Nipple Mount Control Unit (CU 4E-NME/NMI) versus the Fixture Mount Control Unit (CU-4E-FMH)?
- Is there any information for Control Unit possible alternate solutions that Enlighted is compatible with?
- Can the CU-4E-FMH, control two separate 0-10V dimmable drivers controlled by the same circuit to achieve two different light levels?
Can we connect 4 sensors with just one CU-4E-NME or CU-4E-FM in a three-phase (WYE) connection?
- What is the functionality supported by Channel B on the CU?
How many models of Control units are there, and what is the difference between them?
Enlighted provides three different models of the CU-4E control unit.
- CU-4E-FMH: The CU-4E-FMH is for mounting inside of a fixture.
- CU-4E-NMI and NME: These are intended to be mounted on the outside of a fixture or J-Box. The CU-4E-NMI is for fixtures that have sensors mounted INTERNALLY (i.e., within the fixture) or for outdoor locations where weather tightness is needed. The CU-4E-NME is intended to be used with fixtures with sensors mounted EXTERNALLY (i.e., outside of the fixture), such as ceiling-mounted downlights that may have a sensor next to the fixture or in the center of a group of fixtures.
How many control units can I connect to one sensor?
One sensor can control only one Control Unit.
Why are there two 0-10v channels on the CU-4E?
The CU-4E supports dual 0-10V connections for fixtures with two separate dimming channels. Examples of fixtures that require two dimming channels are Tunable White fixtures or up-light/down-light fixtures.
Why do the Enlighted Control Units not work with all Bodine-based Emergency LED Drivers?
Some Bodine emergency solutions support only 2-wire/DALI LED drivers, which do not require a CU. Some Bodine emergency drivers are compatible with Control Units and 0-10V drivers. Contact Enlighted Support for more information.
What's the difference between earlier versions of the Control Unit and the new CU-4E?
The CU-4E is backward compatible with the CU-3E. The CU-4E supports the dual dimming channel capabilities of SU-5 sensors and has a higher load rating than the CU-3E.
The CU-4E is a direct replacement for the CU-3E when it is used with Gen 5 sensors, but when Gen 4 or earlier sensors are installed, additional requirements including adapter cables are needed.
To use the CU-4E with a Gen 4 or earlier sensor, you must use an adapter cable (CBL-CU4-CPL) since the CU-4E has an 8-pin RJ-45 connector with a different pinout than the 6-pin RJ-12 connector used on the CU-3E. An RJ-45 to RJ-45 coupler is also required to correct the gender for the old cable to be plugged in. The coupler is included as part of this same product code. The 6-pin RJ-12 connector is to be plugged into the 8-pin coupler – it will fit. There is no ‘polarity’ to the adapter cable, it can be installed in either direction.
In addition, since the CU-4E does not have ‘fly wire’ cables, the electrician might have to splice some new conductors to be inserted into the CU-4E terminal blocks. Those can even be the old wires cut off of the CU-3E it is replacing.
Refer to the following articles for details:
How can I dim incandescent fixtures with Enlighted CU?
The CU supports 0-10V dimming only. The following types of devices can be used to dim incandescent fixtures: http://digitallighting.com/animationfolder/pd%20Analog%20dimmers.html.
If we replace CUs, do you need to program the sensor?
The CU can be replaced without reprogramming the sensor.
Why does not Enlighted manufacture their own Emergency Control Unit?
Enlighted partners with several manufacturers who make UL924 relays for emergency lighting rather than manufacture this product ourselves. Wiring diagrams and specification sheets are available for all supported devices. Contact Enlighted support for further information.
Does the emergency control unit CU-3E work with fixtures provided with an integral battery pack or just with an emergency system supply such as a generator/inverter? Is there any additional control wiring to connect the emergency control unit to sense loss of power?
After upgrading to CU-4E, Enlighted no longer has an Emergency version of the Control Unit. A separate UL942 device or UL924 driver with integral battery backup is required for all Emergency Fixtures. Enlighted has published the list of approved UL924 devices that can be used with CU-4E. There are devices from several different vendors that support any of the emergency lighting strategies to choose from. Refer to the Line diagrams and manufacturer datasheets for all approved devices in the article Emergency Lighting Solutions.
What is the power output voltage for CU-4E?
- Output voltage: 15.0 V
- Output current: 150 mA
What is the power consumption of the CU-4E?
The CU-4E consumes a maximum of 1W. For more information, refer to the article, Control Unit Power Consumption.
What is the CU-4E power metering accuracy?
When wired correctly, the AC power to the entire fixture flows through the CU, and power consumption accuracy will be +/- 2% or 0.5W (whichever is greater) at nominal operating temperatures (+25°C) or +/- 4% or 1.0W (whichever is greater) over the entire operating range (-40°C to +85°C) of the CU.
Does the Control Unit (CU) output a linear or logarithmic 0-10v dimming?
The Enlighted sensor 0-10V dimming output is a linear dimming curve. A 0-10V (analog) dimming driver (also referred to as a 1-10V dimming driver in some parts of the world) must have a linear dimming characteristic to work properly with the Enlighted system. The output terminals of the CU provides a wiring method to connect to the dimming signals. The sensor, not the CU, generates the actual signals.
Is there a standard J-box size to be used for the control of a CAN light circuit via a Control Unit (CU) and sensor?
The CU-4E-FMH control unit is 5” long, so it must go into a rectangular J-Box such as RACO 951 2-gang box (approximately 6.5” x 4.5”). The CU-4E-NME “Nipple Mount CU with external sensor” is ideal for use with “Can lights,” as the CU can be mounted externally to a J-Box or the field wiring compartment of the light, and the sensor can be placed in the ceiling next to the light.
What are the distinguishing factors for using the Nipple Mount Control Unit (CU 4E-NME/NMI) versus the Fixture Mount Control Unit (CU-4E-FMH)?
The Nipple Mount Control Unit (CU-4E-NME/NMI) is rated for mounting outside of an enclosure, including air-handling spaces. In contrast, the Fixture Mount Control Unit (CU-4E-FMH) must be mounted inside an enclosure (fixture or J-box). The Nipple Mount Control Unit can be mounted to a standard electrical box or fixture wiring compartment via the ½” KO of the box or fixture. It also fits completely inside a standard 4” square J-box as required in some jurisdictions. The Nipple Mount Control Unit is preferable for certain applications where the control unit will not fit in the luminaire, or modification of the luminaire is not possible, such as can lights, architectural lights, gutter lights, wall sconces, narrow pendant lights.
Is there any information for Control Unit possible alternate solutions that Enlighted is compatible with?
Refer to the article Enlighted IoT Ready Drivers and Power Controllers to view the Enlighted compatible drivers.
Can the CU-4E-FMH, control two separate 0-10V dimmable drivers controlled by the same circuit to achieve two different light levels?
No. The CU and the sensor together form one controller unit and can control one “fixture” only
The one set of controls is: AC, Dim Channel A, and Dim Channel B ß these are all built for one controlled unit (i.e. a single fixture) only.
Can we connect 4 sensors with just one CU-4E-NME or CU-4E-FM in a three-phase (WYE) connection?
No. One CU can work with only one sensor. If forced with multiple connections, the firmware will cease to work.
What is the functionality supported by Channel B on the CU?
The separate channels A and B in the Control Unit (CU-4E) helps you to connect to two dimming ballasts for “Tunable White” applications.
- For single channel dimming driver use Channel A.
- For dual channel dimming drivers (Tunable white application) follow the procedure below,
- Step 1: Connect the violet wire (+) from the dimming ballast to Control Unit’s channel A violet Wago terminal. if required, repeat for channel B.
- Step 2: Connect the gray wire (-) from the dimming ballast to Control Unit’s channel A gray Wago terminal on the Control Unit. if required, repeat for channel B.
Article is closed for comments.